Similar Collections

    No collections found

questions

Title
Any number with an exponent of zero is equal to:

Any number with an exponent of zero is equal to:

  1. zero
  2. one
  3. that number
  4. ten
discuss
In the decimal numbering system, what is the MSD?

In the decimal numbering system, what is the MSD?

  1. the middle digit of a stream of numbers
  2. the digit to the right of the decimal point
  3. the last digit on the right
  4. the digit with the most weight
discuss
Which of the following statements does NOT describe an advantage of digital technology?

Which of the following statements does NOT describe an advantage of digital technology?

  1. the values may vary over a continuous range.
  2. the circuits are less affected by noise.
  3. the operation can be programmed.
  4. information storage is easy.
discuss
The generic array logic (GAL) device is ________

The generic array logic (GAL) device is ________.

  1. one-time programmable
  2. eprogrammable
  3. a cmos device
  4. reprogrammable and a cmos device
discuss
The range of voltages between VL(max) and VH(min) are ________

The range of voltages between VL(max) and VH(min) are ________.

  1. unknown
  2. unnecessary
  3. unacceptable
  4. between 2 v and 5 v
discuss
What is a digital-to-analog converter?

What is a digital-to-analog converter?

  1. it takes the digital information from an audio cd and converts it to a usable form.
  2. it allows the use of cheaper analog techniques, which are always simpler.
  3. it stores digital data on a hard drive.
  4. it converts direct current to alternating current.
discuss
What are the symbols used to represent digits in the binary number system?

What are the symbols used to represent digits in the binary number system?

  1. 0,1
  2. 0,1,2
  3. 0 through 8
  4. 1,2
discuss
A full subtracter circuit requires ________

A full subtracter circuit requires ________.

  1. two inputs and two outputs
  2. two inputs and three outputs
  3. three inputs and one output
  4. three inputs and two outputs
discuss
The output of an AND gate is LOW _______

The output of an AND gate is LOW _______

  1. all the time
  2. when any input is low
  3. when any input is high
  4. when all inputs are high
discuss
Give the decimal value of binary 10010

Give the decimal value of binary 10010.

  1. 610
  2. 910
  3. 1810
  4. 2010
discuss
Parallel format means that:

Parallel format means that:

  1. each digital signal has its own conductor.
  2. several digital signals are sent on each conductor
  3. both binary and hexadecimal can be used.
  4. no clock is needed.
discuss
A DAC changes ________

A DAC changes ________.

  1. an analog signal into digital data
  2. digital data into an analog signal
  3. digital data into an amplified signal
  4. none of the above
discuss
The output of a NOT gate is HIGH when ________

The output of a NOT gate is HIGH when ________.

  1. the input is low
  2. the input is high
  3. the input changes from low to high
  4. voltage is removed from the gate
discuss
The output of an OR gate is LOW when ________

The output of an OR gate is LOW when ________.

  1. all inputs are low
  2. any input is low
  3. any input is high
  4. all inputs are high
discuss
Which of the following is not an analog device?

Which of the following is not an analog device?

  1. thermocouple
  2. current flow in a circuit
  3. light switch
  4. audio microphone
discuss
A demultiplexer has ________

 A demultiplexer has ________.

  1. one data input and a number of selection inputs, and they have several outputs
  2. one input and one output
  3. several inputs and several outputs
  4. several inputs and one output
discuss
A flip-flop has ________

A flip-flop has ________.

  1. one stable state
  2. no stable states
  3. two stable states
  4. none of the above
discuss
Digital signals transmitted on a single conductor (and a ground) must be transmitted in:

Digital signals transmitted on a single conductor (and a ground) must be transmitted in:

  1. slow speed.
  2. parallel
  3. analog
  4. serial
discuss
In a certain digital waveform, the period is four times the pulse width. The duty cycle is ________

 In a certain digital waveform, the period is four times the pulse width. The duty cycle is ________.

  1. 0%
  2. 25%
  3. 50%
  4. 100%
discuss
Select the statement that best describes the parity method of error detection:

 Select the statement that best describes the parity method of error detection:

  1. parity checking is best suited for detecting double-bit errors that occur during the transmission of codes from one location to another.
  2. parity checking is not suitable for detecting single-bit errors in transmitted codes.
  3. parity checking is best suited for detecting single-bit errors in transmitted codes.
  4. parity checking is capable of detecting and correcting errors in transmitted codes.
discuss
total MCQs: 428

MCQs

428

Views

218

Best Answers

299

Points

5